
Dunkirk XEB Series 4
Model Number: 42.5-187.5 MBH
XEB Series 4 is a cast-iron gas hot-water boiler.
Technical Specifications
Source: manufacturer spec sheet · checked Sep 27, 2026
Prices depend on sizing, venting and piping in your home, so we quote every installation.
Sizing: the right size comes from a room-by-room heat-loss calculation, not the size of the old boiler or a rule of thumb. Oversized boilers short-cycle and waste fuel; steam systems are sized to the connected radiation instead. See how we approach boiler installation.
Home-Specific Operating Cost Review
No guaranteed annual savings or payback period
Historical Use
Fuel consumption and weather
Current Rates
Utility and delivered-fuel prices
System Design
Load, piping, controls, and temperatures
Full Specifications
- Model Number
- 42.5-187.5 MBH
- Efficiency (AFUE)
- 84.4%
- Boiler Type
- Hot Water Boiler
- Fuel
- natural gas
- Venting
- natural draft
- BTU Input Range
- 43k - 188k BTU
- Domestic Hot Water
- indirect-ready
- In Production
- Yes
- Parts Warranty
- 5-yr parts
- Heat Exchanger Warranty
- 20-yr non-prorated
Specifications sourced from the manufacturer spec sheet, checked Sep 27, 2026.
Ideal For
Homes keeping conventional gas hot-water heat
Expert Review: Dunkirk XEB Series 4
XEB Series 4 is a cast-iron gas hot-water boiler.
Dunkirk reports up to 84.4% AFUE, cast-iron sections with push nipples, 20-year non-prorated limited exchanger coverage and five-year limited parts coverage. Listed input range: 43–188 MBH input. Venting on file: natural draft. Can supply domestic hot water through an indirect tank.
It is best suited to homes keeping conventional gas hot-water heat. Before ordering, a contractor should complete a room-by-room heat-loss calculation, check the distribution system's water temperatures and confirm venting and clearances against the installation manual.
Pros: Non-condensing design that many service technicians already know how to maintain. Often a direct replacement where the existing chimney and piping are retained. Can be paired with an indirect water heater for high-volume hot water. Multiple sizes (43–188 MBH input) allow sizing to a calculated heat loss. Considerations: It is not condensing; compare chimney and piping requirements before retrofitting. Non-condensing efficiency is lower than condensing boilers, so fuel cost matters when comparing options.
Specifications on this page come from the manufacturer documents linked below; always confirm figures for the exact size being installed.
Key Features & Technology
Dunkirk reports up to 84.4% AFUE, cast-iron sections with push nipples, 20-year non-prorated limited exchanger coverage and five-year limited parts coverage.
Listed input range: 43–188 MBH input.
Venting on file: natural draft.
Can supply domestic hot water through an indirect tank.
Advantages
- Non-condensing design that many service technicians already know how to maintain.
- Often a direct replacement where the existing chimney and piping are retained.
- Can be paired with an indirect water heater for high-volume hot water.
- Multiple sizes (43–188 MBH input) allow sizing to a calculated heat loss.
Considerations
- It is not condensing; compare chimney and piping requirements before retrofitting.
- Non-condensing efficiency is lower than condensing boilers, so fuel cost matters when comparing options.
Sizing & Installation Notes
Hot water boilers like the XEB Series 4 are sized from a room-by-room heat-loss calculation. We never match the old boiler's size — oversized units short-cycle, waste fuel and wear out years early.
Every Dunkirk installation starts with a free in-home assessment covering the heat-loss calculation, venting and chimney condition, and gas or oil supply sizing. Learn more about our boiler installation process, or see current rebate and incentive programs that may apply.
Warranty & Protection
Parts Warranty
5-yr parts
Heat Exchanger
20-yr non-prorated
Our Guarantee
100% Satisfaction
All Dunkirk boiler installations by Home+ Air & Heat include our 1-year workmanship warranty, covering labor and any installation-related issues.
Compare the Dunkirk Lineup
| Model | Efficiency | BTU Range | Fuel | Heat Exchanger Warranty |
|---|---|---|---|---|
| XEB Series 4 (this model) | 84.4% AFUE | 43k - 188k BTU | natural gas | 20-yr non-prorated |
| Q95M | 95% AFUE | 80k - 200k BTU | natural gas/propane | 15-yr limited |
| DXL | 83.5% AFUE | Various sizes available | natural gas | — |
| WPSB Series 4 | 84.1% AFUE | 75k - 299k BTU | natural gas | 20-yr non-prorated |
| Royal HE | 95.2% AFUE | 80k - 200k BTU | natural gas/propane | 10 years |
| DXL-K | 84% AFUE | 59k - 235k BTU | natural gas | 20-yr non-prorated |
| Royal CO (combi) | 95.2% AFUE | 80k - 200k BTU | natural gas/propane | 10 years |
| PSB | 82.7% AFUE | 75k - 299k BTU | natural gas | 12-yr limited |
See the full Dunkirk brand page for lineup context, or browse the Best Hot Water Boilers 2027 guide to compare across brands.
Frequently Asked Questions
Ready for a Quote?
Get a free, no-obligation quote for Dunkirk XEB Series 4 installation in Nassau County.
Compare Boiler Brands
See how Dunkirk compares to other top boiler manufacturers.
Similar Boiler Models to Compare
Other hot water boilers with similar efficiency ratings from different brands.



